Skip to content

New combi boilers, fitted from £3,300Combis fitted from £3,300 Get your price in 2 minutesGet your price

Covering every BS, BA, GL, SN, NP and CF postcode

Gas Safe registered, no. 987082 Request a callback Contact Track a job Emergency line 24/7 0117 463 7103

Engineer tightening a pipe fitting on a hot water cylinder

Immersion Heaters

No hot water from the immersion, water far too hot, or the electrics tripping? We find the fault and replace the element, thermostat or switch, usually in one visit.

Gas Safe registered, no. 987082

Plumbing call-out, first hour

£78

Covers the visit and the first hour on site. Further labour and parts are quoted before we start.

Book online0117 463 7103

An immersion heater is an electric element inside your hot water cylinder. For some homes it’s the only way of heating water; for others it’s the back-up for when the boiler is off. When it stops working, it’s nearly always the element, the thermostat or the switch, and it’s usually a quick, tidy repair.

Signs your immersion needs looking at

  • The water stays cold, even with the immersion switched on
  • The water is scalding hot, or the cylinder hisses or bubbles
  • The electrics trip when the immersion comes on
  • The switch light is on, but nothing heats up
  • Water leaking from where the element goes into the cylinder
  • It takes far longer to heat up than it used to

Water scalding hot or the cylinder hissing? Switch the immersion off straight away and book a repair. A thermostat that has stuck on can let the water overheat.

Element, thermostat or switch?

What you noticeMost likely cause
Cold water, switch light onBurnt-out element or failed thermostat
Water far too hotThermostat stuck on
Electrics trip when it comes onElement breaking down inside
Nothing at all, no switch lightSwitch, timer or fuse
Drips around the elementWorn seal, or corrosion where the element fits

We test before we replace anything, so you only pay for the part that has actually failed.

What we do

  1. Test. We check the switch, thermostat and element with a meter to find the real fault.
  2. Drain down. If the element needs changing, we isolate the water and electrics and drain the cylinder below the element.
  3. Replace. We fit the new element, thermostat or switch, with a new seal.
  4. Refill and test. We refill, check for leaks, set the thermostat to 60°C and make sure it heats properly.

Keeping running costs down

Heating water with electricity costs more than gas, so it pays to heat only what you need.

  • Fit a timer, so the immersion runs when you need hot water rather than all day.
  • On Economy 7 or another off-peak tariff, heat the water overnight. Many cylinders have two elements: the bottom one heats the whole tank cheaply at night, and the top one gives a quick boost during the day.
  • Keep the thermostat at 60°C. Below that, bacteria such as legionella can grow in stored water.
  • A well-insulated cylinder keeps water hot for longer, so it needs heating less often.

When a new cylinder makes more sense

On older copper cylinders, a seized element can be hard to remove without damaging the cylinder. If we think that’s a risk, we’ll tell you before we start. If your cylinder is leaking, badly corroded or more than about 20 years old, a new one may be better value than another repair. See hot water cylinders and unvented cylinders.

Plumbing call-out, first hourCovers the visit and the first hour on site. Further labour and parts are quoted before we start.£78
Plumbing labourAfter the first hour. Charged in 30-minute blocks.£54 per hour

All prices include VAT at 20%.

Prefer to talk it through first? Request a callback and we’ll ring you.

Our four house rules, on every job

The price before the work
Our prices are on this site, and every repair is priced and agreed with you before we start.
A properly qualified engineer
Gas work is only ever done by a Gas Safe registered engineer. Ours is carried out by TempZilla (Gas Safe no. 987082).
Honest timings
For urgent jobs (no heating, no hot water or a leak you can’t stop) we aim to attend the same or next working day. If that changes, we tell you.
Straight advice
If a repair makes more sense than a new boiler, or you don’t need a powerflush, we’ll say so.

Questions about immersion heaters

How much does an immersion heater repair cost?

Our plumbing call-out is £78, which covers the visit and the first hour on site. After that, labour is £54 per hour. We tell you the price of any parts before we fit them.

How do I know if the element has gone?

If the immersion is switched on and the water stays cold after a couple of hours, the element or thermostat has usually failed. We test both and replace what's needed.

Why does my immersion trip the electrics?

Usually the element is breaking down inside and leaking current to earth, so your safety switch turns the power off to protect you. Leave it switched off and book a repair. A new element normally fixes it.

How long does an immersion element last?

Often ten years or more, but hard water shortens its life because scale builds up on the element.

Should I leave my immersion on all the time?

No. It's cheaper to heat water when you need it, using a timer or an off-peak tariff. Just make sure the water reaches 60°C each time it's heated.

Is it worth replacing the element on an old cylinder?

Usually, if the cylinder is sound. If it's corroded or leaking, a new cylinder may be better value, and we'll tell you before we start.

Can you fit an immersion timer?

Yes. A timer means the immersion only comes on when you need it, which can cut your bills.

Let’s get you sorted

Book online in a few minutes and we’ll confirm your appointment with you directly.

Call Book online